DEXAPLAN BA 611 - 08-2007 Technical Information download pdf (Page 8)

6 GB

฀฀฀฀฀฀฀฀

 Attention!

฀฀ ฀฀฀฀฀฀฀฀฀฀฀฀฀฀

for the remote control. Do not use any other battery

type.

฀฀ ฀฀฀฀฀฀฀฀฀฀

฀฀ ฀฀฀฀฀฀฀฀

batteries are not suitable because they discharge

themselves.

฀฀ ฀฀฀฀฀฀฀฀฀

the device.

฀฀ ฀฀฀฀฀฀฀฀฀

discharged batteries.

฀฀ ฀฀฀฀฀฀฀฀฀

฀

฀฀ ฀฀฀฀฀฀฀฀฀

฀

฀฀ ฀฀฀฀฀฀฀฀฀

check the supplied items for damage and complete-

฀

฀฀ ฀฀฀฀฀฀฀฀฀

฀฀

฀฀ ฀฀฀฀฀฀฀฀฀฀

not connect it. If in doubt ask your customer service

centre.

฀฀ ฀฀฀฀฀฀฀฀฀

telephone dialler is likely to remain out of operation

for a prolonged period.

Preparing for ﬁrst use

Plan where you are going to locate the device

Check that the alarm and emergency telephone dialler

works properly at the proposed site.

Observe the following points:

Place the alarm unit near a mains outlet socket and

an analogue telephone connection point. Take note

of the cable length required.

฀ ฀฀฀฀฀฀฀฀฀฀฀

฀฀฀฀฀฀฀฀฀

interfere with radio reception.

Monitoring is by means of a motion detector (PIR)

attached to the top of the alarm unit. The position

you select for the device should be in an area of the

building that is likely to be crossed by an intruder, for

example a corridor or stairs.

The motion detector reacts to changing heat sources;

e.g. movement of people within its detection range

(up to approx. 6m over a max. angle of 100 °, from

an ideal mounting height of approx. 0.5 – 2m, see

Fig. G).

฀ ฀฀฀฀฀฀฀฀฀฀฀

Otherwise this will detrimentally affect the proper

functioning of the detector.

As the motion detector reacts to changes in heat,

there should be no sources of heat in detection range,

e.g. heaters, air conditioning units, windows, ovens

or strong draughts.

Pets may also trigger the alarm. Keep pets away from

the monitored areas when the alarm and emergency

telephone dialler is armed or direct the motion de-

tector in an appropriate direction.

The speed of detection also depends on the ambient

temperature. Detection is faster in a cooler environ-

ment.

Motion moving transverse to the motion detector

will be detected faster than motion moving directly

towards it. Position the device in such a way that an

intruder would be most likely to move transversely

to it (see Fig. G, direction of arrows).

Position the alarm unit in such a way that a potential

intruder would not immediately notice it.

Telephone connection

Connect the supplied telephone connection cable

between the telephone line connection “LINE”

and your analogue domestic telephone connection

point. For some countries an adapter is included.

If necessary you can connect a telephone or another

terminal device with an RJ-11 plug cable to the

“PHONE” socket

if the two middle pins of the

RJ-11 plug are wired.

Note: The pin assignments differ from device to device.

Power supply

Remote control:

Push the battery compartment cover

downwards

using light pressure (see Fig. M).

Insert the battery

a, observing the correct polarity

(see marking in the battery compartment).

Push the battery compartment cover back on to the

housing again.

Check that the remote control unit works properly by

pressing the

key

. The check LED

illuminates.

Alarm unit:

9 V block battery (optional, for backup power supply)

Remove the screw

from the battery compart-

ment cover

with a crossheaded screw driver.

Remove the battery compartment cover by pushing

it downwards.

Connect a 9V block battery to the battery connector

Pay attention to the correct polarity.

Now place the connected battery inside the battery

compartment

Push the battery compartment cover back on to the

battery compartment again.

Tighten the screw to fasten the battery compart-

ment cover back into place.

฀฀฀฀฀฀

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 37 38

Comments to this Manuals

No comments

DEXAPLAN BA 611 - 08-2007 Technical Information Page 8

Comments to this Manuals

Related products and manuals for Motion detectors DEXAPLAN BA 611 - 08-2007